OMC Gear Set *400-800 Stringer upper/lower unit gearcase

Basic used OMC 400/800 Stringer and Cobra gears for lower cost repairs
Includes all used parts shown in picture listed (see below).
OMC used gear set photos listed below sold as is contact order desk 1st for availability
Compatible with models with the ball gear that is installed with a nut - does not work with the pre 1972 models that have a press on ball gear.

OMC 800 series and Cobra outdrive lower unit gears
use with 4-1/4 inch hub V6 and V8 engine

22622 GLM aftermarket OMC gear set OEM 435020-437297

P/N 22622 GLM Marine aftermarket OMC Forward, pinion, reverse gear and clutch dog OEM-986980 $310.99

22652 Reverse

P/N 22652 OMC reverse gear with clutch OEM-437297 $311.95

22623 forward pinion 14-26 ratio

P/N 22623 $382.89 GLM Marine aftermarket OMC pinion and forward gear. Note: P/N 21610 pinion bearing (not included)
but should be replace OEM 987670

22625 Clutch dog

P/N 22625 GLM Marine aftermarket OMC clutch dog OEM-337774 $96.95

22624 Reverse

P/N 22624 Reverse gear OEM-910994-914726-915273 $278.95

Heavy duty set 800 series with large hub 4-1/4 inch

22666 V6 V8 with high alloy steel

P/N 22666 New heavy duty GLM gears machined from 8620 forged steel that are 50% stronger but can not be interchange with the standard type $557.95

OMC Hydraulic shift 1978 to 1981 large hub 4-1/4"

22620 forward reverse pinion clutch dog

P/N 22620 Hydraulic shift gear set with clutch 1978 thru 1981 OEM 435088, 437297 $500.00

22621 forward pinion 1978-1981

P/N 22621 Forward / pinion gear set for OMC hydraulic shift years 1978 thru 1980 OEM-435088 $400.00

22625

# 22625 $95.09 OEM 337774

OMC gears 400 series and Cobra with small hub 3-7/8 inch

22630

P/N 22630 Complete gear set including clutch dog. 4 cylinder 400 series years 1982-1985. Cobra 2.3 liter years 1987-1990. 3.0 liter years 1986-1989. OEM 986979 $499.89

22631

P/N 22631 4 Cylinder 400 series pinion and forward gear set. Cobra years 1986 thru 1989. 13/26 Gear ratio. OEM 436746 $508.95

22632 Reverse

P/N 22632 revers gear OEM 345992 $212.95

22633 Clutch dog

P/N 22633 Clutch dog OEM 323664 $99.95

Used gear set for 3.0 liter 4 cylinder, 4.3 liter V6 and 5.7L Chevy 350 or 5.8L Ford 351
G 21-16	G 21-16 Used V8 gear set for 5.7L Chevy 350 or 5.8L Ford 351 $349.95
E 21-19	E 21-19 Used V6 or inline 6 gear set for 165 model or 4.3L Chevy $349.95
C 21-19	C 21-19 Used 6 cylinder gears for 165 model or 4.3L Chevy $349.95
B 21-16	B 21-16 V8 small block gear set Chevy or Ford $349.95
A 21-17	A 21-17 V8 small block gear set Chevy or Ford 305 or 302, 5.0L only $349.95
H 21-20 V6	H 21-20 3.8L 229 V6 Buick only $349.95
L 19-21 4 Cylinder	L 19-21 Older 4 cylinder 1967 to 1977 outdrives $349.95
I2 V8 SHAFT

OMC 800 series and Cobra outdrive lower unit gears use with 4-1/4 inch hub V6 and V8 engine
22050 GLM Marine aftermarket parts	P/N 22050 GLM Marine aftermarket kit years 1973 to 1986 $220.95
22050 GLM Marine aftermarket parts	P/N 22050 GLM Marine aftermarket kit years 1973 to 1986 $220.95
22010 intermediate housing	P/N 22010 GLM aftermarket intermediate housing ball gear 908063 $142.95
Removed	1968 T0 1972 OMC press on ball gear intermediate housing $399.15 Note special seal P/N 86370 will be required based on the shaft being used
22020 OEM 908089	P/N 22020 GLM aftermarket upper ball gear #908089 $189.99
OMC parts for years 1968 to 1972
U-001 Press on shaft	U-001 New OMC press on ball gear years 1968 to 1971 #314579 $399.15 Limited stock call for availability Note 680 Loctite retaining compound is required for installation. Above, installed (pressed) onto a used OMC intermediate drive shaft. $499.15
Press on 165 hp 6 cylinder inline	U-022 Used OMC intermediate housing press on ball gear years 1965, 1966 and 1967 #0908063 from 165 hp 6 cylinder in-line engine
Intermediate housing shaft ball gear retainer	U-002A New ball gear, seals, o-ring and nut for years 1973 to 1985. Comes with used OMC intermediate drive shaft OEM number 383177 $379.29
Used shaft and retainer with new seals o-ring	U-002B OMC intermediate shaft assembly with used ball gear (same as above) $279.29
	U-003 Intermediate housing press on bearing retainer #316490 (used retainer with new seals and o ring) $129.29
68015 Loctite 680 installing seals tapper area	680 Loctite should be installed on tapper area and the shaft tapper. This is required to seal upper part on the outdrive. Loctite should also be used when installing oil seals in a used bearing retainer. Note 680 Loctite will fill a void in bearing retainer of up to .030 if per-coated 24 hr. ahead of time, then one more again when installation takes place please see video. $29.15
Johnson gasket compound 508235	Evinrude-Johnson outboard gasket sealing compound with convenient brush on lid. OEM P/N 508235 for any gasket and o rings or new oil seal-bearing retainer installation. Never hardens or dries out, clean easy with Varsol or lacquer thinner. Note P/N 508235 Johnson gasket compound must be mixed completely each time used to maintain viscosity. $24.95
51531 loctite 515 gasket eliminator for covering nuts installing plugs	P/N 327361 System matched - Gel sealant 2 (seals metal to metal surfaces) 1.69 oz. or 50 ml. $14.15
bearing remover tool	P/N 90150 Universal puller plate tool OEM 91-37241 $119.95